Choosing a machine can be complicated. From floor space issues to getting everyone up to speed and able to use it successfully. Then there are the details such as how much is it? And when can I have it on the floor. There are an untold number of people selling finishing machines and it can be tough to sort through them. You want a machine that will do the job and not be out of service every time you turn around. This is where you can help yourself by weeding through the different avenues available to you.
Murphy's law
I am no history expert by any means, it seems that Murphy's law is credited for better or worse to Capt Edward A Murphy. I always knew it as "What can go wrong will". I have no idea if that is where it started but unfortunately the statement seems to hold true.
Making the process better
My grandfather used to look at newer cars and say that they were too complicated. He was looking at the car as it would be in a few years when it would need repair. He was not afraid of the new technology but rather what problems it would bring later. Other than, the robot overlords taking over the world part, the rest of his argument made sense. Just because you can get a new anything with all kinds of add-ons and upgrades does not mean you should. If you get that new machine can your current staff operate and service it? If you need to bring in an outside factory tech for every little thing that goes wrong, the cost will certainly pile up over time. Keeping points like this in mind are important, as they are part of the big picture and the machine's True cost. It may not be an upfront cost but you are going to pay for it one way or the other.
Loewer DiscMaster information
In an effort to to provide more and better information on the Loewer machines I will be putting together more video content. The hope is to provide a repository of information to help you with a machine you have or one you are looking to purchase. These will range from a basic walk around to single topics in more depth. I will do my best to get content produced and uploaded on a consistent basis and add to it topics presented as areas of interest. So if you have ideas for content you think would be helpful please feel free to share your suggestions. The videos will be on our website as well as Youtube to make it easier to find where you may be looking for it. So feel free to post comments or to let me know what you would like to see covered.
Saving money?
As is always the case looking for ways to save money often leads to looking at many different paths. It can be the time invested in a process to vendor supplies and services. One area to look at that often hides savings is finishing.
Why is a bur a problem?
Don't monkey around with finishing, do it once and do it right.
Stroke Sander articulating mount makes 3D parts easy
All stroke sanders "should" have a flat table of some fashion to allow placement of parts or material being worked. The size and weight capacity tends to be where the conversation ends. With the better machines you may even have a twin belt setup to make life and use of the machine better still. But when you get to the very best of stroke sanders an articulating mount comes into play. What they allow you to do is have the machine hold a given 3D or formed part at just about any angle or height. If you are working with a range hood for example, you can have the mount hold the part at the needed angle while you grind down the weld and blend the finish with the second belt. Before you would need to make a fixture to hold the part and it would be a one off fixture no less. With the articulating mount that is not an issue any longer. Together the features of the better stoke sanders save time per part by not needing fixtures and belt changes. Then add in the fact you don't need to remove the part from the machine for a belt or fixture change and you cut down on injury to the part as well as the staff. Watch the video at the link below to see the mount on a KBM stroke sander. And as always feel free to send in any questions we are happy to help.
KBM Stroke sander in stock
Due to the demand and lead time we rarely get a unit in stock. We have managed to get an extra unit with our current delivery. The KBM stroke sander is built in Germany and is the twin belt design. This allows you to grain and blend without changing belts or unloading the parts. It is also equipped with the articulating mount for doing formed, welded or odd shaped parts. This is a very flexible configuration and by far the most popular.